Steering Race Removal Advice?

Discuss all things 1970 & later Airheads right here.
Duane Ausherman
Posts: 6008
Joined: Thu Aug 12, 2010 12:39 pm
Location: Galt California
Contact:

Re: Steering Race Removal Advice?

Post by Duane Ausherman »

Yes, Ken, I have done it a few times with the oxy torch. The trick is to heat the race enough that it just starts to puddle and move around it sort of keeping the puddle going. The frame paint is ruining, but the race falls out exactly the same as with arc welding.

I seem to remember doing it as a fun test on a frame that was going in for new paint. However, I wouldn't chose to do it that way again and here is why. Once the race is out, one must now protect that cavity from the new paint. The old race can be stuck back in with something that is easy to remove and then the race protects the cavity from the new paint.
Ask the Indians what happens when you don't control immigration.
ME 109
Posts: 7306
Joined: Tue Aug 03, 2010 3:00 am
Location: Albury, Australia

Re: Steering Race Removal Advice?

Post by ME 109 »

Ken in Oklahoma wrote: I would think a stick welder would be nearly impossible to use due to that long welding rod waving around.
Ken
The trick is to cut the welding rod to about 4" long. I use a 2.5mm general purpose electrode.
Lord of the Bings
User avatar
Airbear
Posts: 2886
Joined: Tue Aug 03, 2010 10:02 am
Location: Oz, lower right hand side, in a bit, just over the lumpy part.

Re: Steering Race Removal Advice?

Post by Airbear »

This has worked for me:

Image

It's a length of 8mm stainless rod, bent using a vise and then cut off to leave that angled point. It won't work on all steering head bearings - some have a too-large radius on the inner edge. For that situation I've resorted to the weld method as ME109 describes, or welding a little piece of flat steel across the bearing and then tapping out with a drift.
Charlie
and Brunhilde - 1974 R90/6
Image

Graduate, Wallace and Gromit School of Engineering and Design (Pending)
User avatar
George Ryals
Posts: 510
Joined: Tue Aug 03, 2010 10:22 am
Location: Stone Mountain, GA

Re: Steering Race Removal Advice?

Post by George Ryals »

Once you get the race out, grind a couple of 1/4" radius notches 180 deg. apart in the ledge that the race seats against. Next time will be easy with a drift.
Smile it's contagious!
'74 R90S, '67 /2 Conv w/sc, '66 R50/2
'74 Harley FXE, '72 Harley FLH w/HD sc
'69 BSA 441 Victor Special, '74 R90/6 Basket case
'85 R80RT wreck for parts
Duane Ausherman
Posts: 6008
Joined: Thu Aug 12, 2010 12:39 pm
Location: Galt California
Contact:

Re: Steering Race Removal Advice?

Post by Duane Ausherman »

Great idea George, thanks.
Ask the Indians what happens when you don't control immigration.
ME 109
Posts: 7306
Joined: Tue Aug 03, 2010 3:00 am
Location: Albury, Australia

Re: Steering Race Removal Advice?

Post by ME 109 »

Duane Ausherman wrote:Great idea George, thanks.
That does seem like a good idea!
Lord of the Bings
User avatar
Ken in Oklahoma
Posts: 3182
Joined: Tue Aug 03, 2010 5:10 pm

Re: Steering Race Removal Advice?

Post by Ken in Oklahoma »

ME 109 wrote:
Duane Ausherman wrote:Great idea George, thanks.
That does seem like a good idea!
I'm going to chime in too. Good idea.

Ken
____________________________________
There's no such thing as too many airheads
User avatar
Airbear
Posts: 2886
Joined: Tue Aug 03, 2010 10:02 am
Location: Oz, lower right hand side, in a bit, just over the lumpy part.

Re: Steering Race Removal Advice?

Post by Airbear »

I'll be doing that, thanks.

ps: I reckon George must be one of those people who is thinkin' all the time.
Charlie
and Brunhilde - 1974 R90/6
Image

Graduate, Wallace and Gromit School of Engineering and Design (Pending)
sprints@pldi.net
Posts: 100
Joined: Fri Apr 06, 2012 10:11 am

Re: Steering Race Removal Advice?

Post by sprints@pldi.net »

Hey Airbear, I made your little 'hook tool' from a 5/16 rod and it worked excellent! The bottom was more difficult than the top and I had to sharpen the point on my tool once but once you get it started moving it's a piece of cake - Rod
Post Reply