Please allow me to introduce myself ....

Discuss all things 1970 & later Airheads right here.
ME 109
Posts: 7307
Joined: Tue Aug 03, 2010 3:00 am
Location: Albury, Australia

Re: Please allow me to introduce myself ....

Post by ME 109 »

I have worked hard to obtain a phd in new (bmw) mistakes. :roll:
Lord of the Bings
oldsoul70
Posts: 10
Joined: Sat Sep 11, 2010 12:39 pm
Location: CDA, ID USA

Re: Please allow me to introduce myself ....

Post by oldsoul70 »

Thanks for the posts guys! This is going to be my over the road hauler so I want to have every thing tight and right. I agree that the time to change the tranny is the minuet I have a replacement. (and an afternoon) Yep, I have the log book started and I'm bugging the former owner ( who's a friend) for the records that came with the bike when he got it."It's around here somewhere" :| I'm hoping if I do tranny fluid changes like mad, maybe every couple tanks of fuel, I can buy myself another season. That being said I would like to put a few thousand on it this year. Maybe 10k? :D

In regards to the fuel flow. The bike sat for the better part of 10 years before I got it so there is some serious chit in the tank. The inside of the tank has a orange coating that I'm thinking is a failed tank seal attempt? Are they orange from the factory? I've used POR 15 with good results in auto tanks before so I've been thinking of doing that. I've received some advise to clean the tank the best I can and just run with some extra filters for what if's. Any thoughts?

Oh and just to open up a can.... what's the best input shaft spline lube?
User avatar
Zombie Master
Posts: 8821
Joined: Sun Aug 22, 2010 12:21 am
Location: Vancouver Island BC Canada

Re: Please allow me to introduce myself ....

Post by Zombie Master »

what's the best input shaft spline lube?

Oh Dear! :shock:

Honda Moly Grease
Any and all disclaimers may apply
Deleted User 61

Re: Please allow me to introduce myself ....

Post by Deleted User 61 »

oldsoul70 wrote: In regards to the fuel flow. The bike sat for the better part of 10 years before I got it so there is some serious chit in the tank. The inside of the tank has a orange coating that I'm thinking is a failed tank seal attempt? Are they orange from the factory? I've used POR 15 with good results in auto tanks before so I've been thinking of doing that. I've received some advise to clean the tank the best I can and just run with some extra filters for what if's. Any thoughts?

Oh and just to open up a can.... what's the best input shaft spline lube?
Orange is original. Have you removed the petcocks yet, to see if any junk comes out with them? Was it stored all that time with old fuel in it?
I've yet to see the need for an external fuel filter. Some folks wouldn't leave home without them. I have the straight Karcoma on mine, and it has two screens - one covering the tubes inside the tank, and one right above the nipple to which the fuel line attaches.
(Thanks to Hucky's for the image.)

Spline lube? My personal favorite is Honda Moly 60. There are several good moly grease's out there, but the Honda is easy to find. It should be available at a Honda dealership, but call ahead.

Here is a source online: http://www.bernardiparts.com/Honda-Moly ... -0001.aspx
One tube should last you your lifetime. Also good on rear wheel splines. Sparingly but thoroughly in both places.
User avatar
R90Steve
Posts: 51
Joined: Tue Nov 30, 2010 1:21 am

Re: Please allow me to introduce myself ....

Post by R90Steve »

I have seen rust and dirt that was small enough to go through the screens, yet big enough to plug pilot jets. A filter that caught the fine rust, restricted the flow enough to make the last of the gas in the tank not drain.

Some guys over on a Triumph forum use an old clothes drier dedicated to cleaning gas tanks. They put variuos sizes of nuts, bolts and ball bearings in the tank before wrapping it with padding and let'er rip. Gentle cycle?
Duane Ausherman
Posts: 6008
Joined: Thu Aug 12, 2010 12:39 pm
Location: Galt California
Contact:

Re: Please allow me to introduce myself ....

Post by Duane Ausherman »

I have something about fuel flow and the screens on my website. I still have one don't I? I haven't looked lately.
Ask the Indians what happens when you don't control immigration.
Deleted User 61

Re: Please allow me to introduce myself ....

Post by Deleted User 61 »

Duane Ausherman wrote:I have something about fuel flow and the screens on my website. I still have one don't I? I haven't looked lately.
Let's see......

Yep! there it is!

Duane - Top of the Heap!
oldsoul70
Posts: 10
Joined: Sat Sep 11, 2010 12:39 pm
Location: CDA, ID USA

Re: Please allow me to introduce myself ....

Post by oldsoul70 »

Yea I have the straight Karcoma to but the screens where torn, removed and in one of the saddle bags when it came to me. I did a gas tank rinse in the fall and threw on some large inline filters in an attempt to get some pre snow miles on. I just shook the tank around and rinsed it out with old gas a few times. The results where a bit alarming. I washed out a half cup on rusty, orange, flaky mess. It did fine the month I rode it but it would be nice to know it's repaired rather than counting on the filters.

Honda moly it is!



Duane, your web site is great. I read and reread your tranny info before purchase on this bike. Very helpful and got me even more excited about BMW's. Thanks
User avatar
pkboxer
Posts: 118
Joined: Tue Aug 03, 2010 8:50 am
Location: Cincinnati

Re: Please allow me to introduce myself ....

Post by pkboxer »

Oldsoul,

Filling the tank with vinegar for a week or so will remove the old liner and not damage the outer paint.

This kit is really nice too and you can do it, again, w/o messing up the outer paint too....

http://www.por15.com/prodinfo.asp?number=CTRK
'74 - R90/6
Deleted User 61

Re: Please allow me to introduce myself ....

Post by Deleted User 61 »

Yeah - if the orange liner is flaking off, it is time to re-do it. :(
Post Reply